![]() ![]() ![]() The heat and look of a glowing fire will create an atmosphere of The style you like best, and put the unit in the room where you spend the Room, most small to medium size heaters will suit your needs. If you simply want to enhance the ambiance of a There is no good or bad reason forīuying a wood-heat system. Some people will buyĪ heater simply to enhance the ambiance of a room, while others will buyĪ heater as their main source of heat. Important that you clearly identify what your needs are. A wood heater that meets this Standard will generally comply with the regulation in place.īefore answering this question, it is very It must also be noted that in Canada, the CSAB415.1-10 Standard is equivalent to the EPA Standard. Certain municipalities may also have by-laws that require the installation of an EPA or CSAB415.1-10 wood heater, even though the province does not have an official regulation on wood heating. Exceptions apply for certain categories of products, such as decorative fireplaces. NOTE: If you live in the United Sates, British Columbia, Ontario, Quebec, Nova Scotia, New Brunswick or Newfoundland, EPA certified wood heaters are mandatory. You will help the environment and reduce your wood consumption by up to 30%. As a result, if the style and size of the heater you are looking for is available in a certified version, it is highly recommended that you invest in this advanced combustion technology. Furthermore, it must be noted that certified heaters release up to 90% less particles into the atmosphere, which makes wood a renewable and clean source of heat. However, if your goal is to heat on a regular basis, the extra dollars will prove to be a good investment. If you are looking for ambiance, a temporary heat source in a cottage or a camp, or a simple back-up heat source in case of power failure, you do not necessarily need to invest more money in order to buy an EPA or CSAB415.1-10 certified wood heater. You first have to identify what your needs are. Before setting up your unit, refer to the installation manual. ** Some appliances have been tested with a low ceiling. * The information given on the certification label affixed to the appliance always overrides the information published in any other media (owner's manual, catalogues, flyers, magazines and/or web sites). 1 inch = 25.4 mm)Ĭlearance – top (measured from the platform on which the appliance is installed)**Ĭlearance – combustible side mantle to unitĬlearance – minimum floor protection in front of the applianceĬlearance - from the shelf to the base of the fireplace * Specific components may be required depending on the chimney manufacturer. Tested and listed as per applicable standards Stainless-steel secondary-air system improving gas combustion Glass surface – dimensions (Width X Height) ( 9) This appliance is officially tested and certified by an independent agency. ( 8) The optimum heat transfer efficiency is for the low burn rate (using HHV) and represents the appliance’s ability to convert the energy contained in the wood logs into energy transferred to the room in the form of heat and does not take into account the chemical losses during combustion. ( 7) Optimum overall efficiency at a specific burn rate (LHV). ![]() ( 6) Performances based on a fuel load prescribed by the standard at 7 lb/ft³ and with a moisture content between 19% and 25%. ( 3) As measured per CSA B415.1-10 stack loss method. The moisture content is between 19% and 25%. The specified loading density varies between 7 lb/ft³ and 12 lb/ft³. Other performances are based on a fuel load prescribed by the standard without any reloading between start and finish. ![]() ( 2) The maximum heat output (dry cordwood) is based on a loading density varying between 15 lb/ft³ and 20 lb/ft³ and reloading intervals ranging from 60 to 120 minutes. The recommended heated area for a given appliance is defined by the manufacturer as its capacity to maintain a minimum acceptable temperature in the designated area in case of a power failure. ( ) Recommended heating area and maximum burn time may vary subject to location in home, chimney draft,heat loss factors, climate, fuel type and other variables. ( 1) Values are as measured per test method, except for the recommended heating area, firebox volume, maximum burn time and maximum heat output. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |